焊工操作技能评定
发布时间:2012-03-02 来源:文档文库
小
中
大
字号:
焊工操作技能评定
1.目的/Goal 通过技能评定,增强焊工的质量意识,激发焊工提高自身操作技能,改善产品焊缝质量,增强产品的市场竞争力。
2. 焊工考试评定
焊接考试合格与否由制造部进行根据试验结果和焊缝外观裁定。
3. 参加人员安排
一、车间所有焊接作业人员,根据岗位不同可以选择不同的考试评定项目。 二、只有在考试合格后,才能焊接相对应的项目。
4. 评定事项安排
一、根据生产与人员匹配情况,可以随时安排考试,考试完后,由焊接考试评定委员会评定,评定合格后,颁发焊工上岗证,即可从事焊接工作。
二、焊工上岗证,首次考试有效期为六个月,之后考试有效期为12个月。在上岗证到期前2个星期,上岗证持有者要向制造部申请复审,否则自上岗证过期之日起,不得从事焊接工作。
三、焊工岗位不得无证上岗,不得持过期证件上岗。
5. 考试项目Test item 一、焊接焊接方法为:氩弧焊,气保焊,手工焊,钎焊 (Type of the welding,Gas tungsten arc welding (GTAW, Gas metal-arc welding(MIG,
二、考试材料,根据公司实际情况,氩弧焊管子对接使用304不锈钢材料,管板材料为管子材料为304,板材为20#钢,其他焊接项目均为20#,钎焊为紫铜与紫铜焊接,紫铜与不锈钢焊接,紫铜与黄铜焊接,紫铜与碳钢焊接,换热器小U弯焊接。(Type of material, according the status of our company, use the stainless for the tube butt join, use the mild steel for the plate, the red copper, stainless, steel for blazing 三、焊接练习工艺与方法
a 氩弧焊焊接操作方法参见《WI-13-? 手工钨极氩弧焊作业指导书》 b 大管径钎焊操作方法参见《WI-10-? 钎焊作业指导书》
c 小U弯钎焊操作方法参见《WI-10-? 钎焊作业指导书》、《WI-46-?
冷风机作业指导书》及《WI-47-?冷凝器作业指导书》
四、焊接接头形式与位置, 详见下图(Type of the Joint)
1. 平板对接(butt joint, Single-Vee Groove weld
焊工操作技能评定
Flat position welding
Horizontal position welding
Vertical position welding
2. 管子对接
All position welding
Horizontal rolling welding
3. 管板对接
Vertical fixed Tube-plate joint Acceptable types of welded nozzles is full penetration
焊工操作技能评定
型弯头焊接试件图说明:考试时可以制作一些盘管,胀好管后,插上一些型弯头,每次考试小弯的数量不得少于30只
综合以上,焊接项目一共有如下几种:(So we need these items
No. 焊接方法 焊接材料 焊接接头形式
Type of welding Type of material
Type of Joint 1 氩弧焊GTAW(TIG 不锈钢 stainless 管子对接水平转动
Tube butt, Horizontal rolling welding 2 氩弧焊GTAW(TIG 不锈钢 stainless 管子对接水平转动
Tube butt, Horizontal fixed welding 3 氩弧焊GTAW(TIG 20#钢,Mild steel 垂直固定管板接头
Vertical fixed Tube-plate joint 4 气保焊GMAWN(MIG 20#钢,Mild steel 平板水平焊接,
Plate butt flat position welding
5 6 7 8 气保焊GMAWN(MIG 20#钢,Mild steel 气保焊GMAWN(MIG 20#钢,Mild steel 气保焊GMAWN(MIG 20#钢,Mild steel 钎焊
Braze 平板水平接头,
Plate butt flat position welding
平板横焊接头,
Plate butt flat position welding
平板立焊接头,
Plate butt vertical position welding
9 小U弯钎焊
紫铜-紫铜,
Red copper – Red copper 紫铜-紫铜, Red copper – Red copper
焊接方法分为如下:
a 氩弧焊(GTAW),管子对接(Tube butt),水平转动(Horizontal rolling ,不锈钢(stainless
焊工操作技能评定
b c d e f g h i j k